Open Access
Issue
2017
18th International Congress of Metrology
Article Number 14008
Number of page(s) 4
Section Dynamics of pressure / Les dynamiques de la pression
DOI https://doi.org/10.1051/metrology/201714008
Published online 18 September 2017
  • Hoffmann, K.; “An Introduction to Measurements using Strain Gauges“, Hottinger Baldwin Messtechnik GmbH, Darmstadt, Germany, 1989, pp. 145
  • Kreuzer, M. “High-precision measuring technique for strain gauge transducers“ Internal publication of Hottinger Baldwin Mestechnik, GmbH, Darmstadt, Germany, 1999
  • Kleckers, T., Graef, M. “High capacity reference transducer for tensile forces“¸ IMEKO 22nd TC3, 12th TC5 and 3rd TC22 International Conferences 3 to 5 February, 2014, Cape Town, Republic of South Africa
  • Kleckers, T, Precise radial symmetric shear beam force transfer transducer for compression force; XXI IMEKO World Congress, Sept. 2015, Prague, Czech Republic.
  • Schäfer, A.; “Force, strain and pressure transducers based on foil type strain gauges“, Proceedings of Eurosensors; XXII conference, Dresden, Germany, October 2008
  • Schäfer, A. “New possibilities with a high pressure measuring chain consisting of reference pressure transducer P3 TopClass BlueLine and DMP 41 high-precision instrument“, PTB Report TH6, Brunswick, Germany, April 2016
  • Haller, M. Viel, W.; Schäfer, A.; “Enhancement of the measurement characteristics of pressure transducers up to 15000 bar through monolithic measuring design and foil type strain gauges“, Proceedings of XIX IMEKO World Congress Lisbon, Portugal, 2009
  • Schäfer, A.; et al.; “A new type of transducer for accurate and dynamic pressure measurement up to 15000 bar using foil type strain gauges“, XVII IMEKO World Congress 2003, Dubrovnik, Croatia, 2003
  • Eichstädt. S., Esward, T. J., Schäfer, A. “On the necessity of dynamic calibration for improved traceability of mechanical quantities“ XXI IMEKO World Congress, Sept. 2015, Prague, Czech Republic.
  • Schäfer, A.; “Dynamic measurements as an emerging field in dynamic metrology“; PTBMitteilungen 125(2015) Volume 2
  • IEEE 1451.4 Standard for Smart Transducers Secretary, issued by IEEE 1451.4 Standard Working Group, 1451.2WG, 2004
  • Schäfer, A. “Challenges in dynamic torque and force measurement with special regard to industrial demands“, BIPM Workshop on Challenges in Dynamic Measurements
  • Schäfer, A. “Development results for static and dynamic torque measurement“, Proceedings of torque symposium of “Zentrum für Konstruktionswerkstoffe”, MPA (State Material Testing Institute), Darmstadt, Germany, 2014
  • Schäck, M. Underestimated impact of measuring cables on high-precision carrier frequency amplifier results and compensation methods there for XXI IMEKO World Congress, Sept. 2015, Prague, Czech Republic.
  • Schäfer, A.; Kitzing, H.; “DMP41- a new chapter of ultra-precision instrument for strain gauge transducers“, XX IMEKO World Congress, September 2012, Busan, Republic of Korea
  • Schäfer, A.; “The ultra-precision instrument DMP41-first experience & appropriate filter settings“, IMEKO 22nd TC3, 12th TC5 and 3rd TC22 International Conferences, February, 2014, Cape Town, Republic of South Africa
  • Schäck, M.; “High-precision measurement of strain gauge transducers at the physical limit without any calibration interruptions“ IMEKO 22nd TC3, 12th TC5 and 3rd TC22 International Conferences, February, 2014, Cape Town, Republic of South Africa
  • Vollmert, R. ; Ramm, G. “Realization, maintenance and dissemination of the measurand >>AC voltage ratio in mV/V<< for strain gauge measurements“, Proceedings of the 17th International Conference of IMEKO TC3, Istanbul, Turkey, 17-21, September, 2001
  • Ramm, G. “ Investigation of bridge standards for use in strain-gauge measurements“ Reports in Applied Measurement RAM, Vol. 6 (1990), No. 1, pp. 26–30
  • Ramm, G.; Peters, M. “Investigation of the Calibration Signal of Force Measuring Devices“. IMEKO Force and Mass 1986, Amsterdam, Conference Digest, ISBN 90-247-3351-0, pp. 267–273
  • Ramm, G. „Untersuchung des Fehlverhaltens eines Brückennormals vom Typ BN 100“ PTB Report PTB-E-30, ISBN 3-88314-655-2, April 1978
  • Crößmann, F. “Investigation of the calibration capabilities of a 1 kN·m reference calibration machine”, IMEKO TC3/ TC5/TC22 in Helsinki, Finland, May 2017
  • Kleckers, T. “New reference load cells for tension and compression with capacities of more than 1 MN”, IMEKO TC3/ TC5/TC22 in Helsinki, Finland, May 2017
  • Schäck, M. “Long term proven and optimized high-precision 225 Hz CF technology in a universal DAQ”, IMEKO TC3/ TC5/TC22 in Helsinki, Finland, May 2017
  • Schäfer, A. “Evaluation of dynamic measurement uncertainty for industrial applications” IMEKO TC3/ TC5/TC22 in Helsinki, Finland, May 2017